Most teams start their battery passport project by filling in data for each model. That's the right place to start, and the wrong place to stop. Article 77(1) of Regulation (EU) 2023/1542 requires an electronic record for each LMT battery, each industrial battery above 2 kWh and each EV battery placed on the EU market from 18 February 2027. One e-bike model sold 8,000 times means 8,000 passports.
This article explains how model data and unit data fit together, what the identifier and the QR code have to do, and what your factory needs from you.
Model data and unit data
Almost all of the 71 data points in the Commission's guidance (v3.2) are the same for every battery of a model: chemistry, composition, rated capacity, voltages, cycle life, the declaration of conformity, the dismantling information. A small set is different for every unit:
- The unique battery identifier (#1), which every passport needs.
- The manufacturing date (#9), and in practice often the plant (#8) if a model is built in more than one place.
- The dynamic data in the state-of-health part (capacity fade, battery status and the rest), which starts at its placing-on-the-market value and changes over the battery's life.
The efficient way to build passports is therefore model first, units second: complete and check one model passport, then issue a unit passport for every serial number, each inheriting the model data and adding its own identifier and date. Nobody types the chemistry 8,000 times, and a correction to the model reaches every unit.
The identifier: what it has to do
Article 77(3) links the passport to a unique identifier assigned by the economic operator placing the battery on the market. The Regulation doesn't prescribe a format. In practice the identifier has to:
- be unique per battery, permanently: never reused, even after the battery has been recycled;
- be resolvable, meaning a scanner or a system can turn it into the passport's address;
- survive the supply chain, so it can't depend on an internal ERP number that changes when you switch systems.
Most companies end up with GTIN + serial number under GS1 standards: the GTIN identifies the model (you may already have one on the packaging), and the serial identifies the unit. If you don't have GTINs yet, you get them from your national GS1 organisation. It's a short administrative step, but plan for it.
The QR code: what it has to do
Article 77(3) makes the passport accessible through the QR code referred to in Article 13(6), linked to the battery's unique identifier. Two practical rules:
- One code per battery. A model-level QR code on the box doesn't meet a per-battery obligation.
- The code should never need reprinting. The passport will change (state-of-health updates, status changes, new guidance versions), so the QR code must point at a stable address, not at a file.
A GS1 Digital Link URI does both. It encodes GTIN and serial in a web address (for example https://id.example.com/01/04012345000010/21/SN000123) that any phone can open and any system can parse. The address stays fixed while the passport behind it is updated.
About the label itself: the label content and format under Article 13 and Annex VI depend on an implementing act on the label format, which has not been adopted yet, and the label requirements apply 18 months after it. Ask your legal adviser how Article 13's dates apply to your QR marking. In practice, plan the QR code for February 2027 anyway: the passport has to be accessible through it, and a factory needs months of notice to change its labels.
What your factory needs
This is where projects stall: the factory is usually outside the EU, and it prints whatever file it receives. Give it something it can use:
- A serial list or range per production batch, agreed before production. Example:
SN000001toSN008000, zero-padded to a fixed width. - One QR code per serial, as SVG for packaging artwork or PNG for quick checks, and as ZPL if the line uses industrial label printers (Zebra and compatibles).
- A CSV linking each serial to its passport address, so the factory, your warehouse and your ERP can cross-check what was printed.
- A test print on the real label material before the batch. QR codes that are too small, or printed on curved or glossy surfaces, fail scanning far more often than people expect.
Batteries inside products
For an e-bike or a scooter, the passport belongs to the battery, not to the vehicle. The QR code has to be on the battery, which matters for designs where the battery sits inside a frame. For replaceable LMT batteries, think about where the code is visible when the battery is removed: repairers and recyclers are the people who will scan it.
A realistic timeline, counted back from 18 February 2027
| When | What |
|---|---|
| Now | Get GTINs if you need them; agree the identifier scheme with your supplier |
| 8–10 weeks before shipment | Model passport complete and checked against the Commission's battery schemas |
| 6 weeks before shipment | Serial ranges agreed; print files (QR, ZPL, CSV) sent to the factory |
| 4 weeks before shipment | Test print scanned and approved on real label material |
| Shipment | Unit passports live behind every QR code before the batteries are placed on the market |
Batteries placed on the EU market before 18 February 2027 don't need a passport retroactively. What counts is the date each battery is placed on the market, so containers that arrive in early 2027 are already in scope.
How we handle it
In our service, the model passport is built in the first two 14-day sprints from whatever data you have. Unit passports are then issued from your serial list or range in one step: every unit gets its own identifier, GS1 Digital Link QR code and signed passport. The factory receives a print pack with a CSV, QR codes as SVG or PNG, and ZPL label files. Later state-of-health updates can come in by API, so the QR code on the battery never changes.
To check what's still missing for your models, start with the free 71-point checklist, or book a call and bring your serial numbering scheme.
Not legal advice. The regulation text is binding.