Skip to main content
All Articles

Battery Passport for Non-EU Manufacturers: Who Is Responsible, and What Your EU Importer Needs From You

If you make batteries in China, India, Turkey, the UK or the US and sell them in the EU, the battery passport obligation from 18 February 2027 lands on whoever places them on the EU market. Here is who that is, what data they will ask you for, how the work is usually split, and the timeline counted back from the deadline.

Ileana Sofronie 9 min read
Battery Passport
EU Battery Regulation
Importers
Exporting to the EU
Supply Chain

Most battery passports that will exist in February 2027 describe batteries made outside the EU. The cells come from China, Korea or Japan; the packs are assembled in China, India, Turkey, Vietnam or the US; and an EU importer sells them. The regulation, however, is written for the EU market, so the first question every exporter asks is the right one: is this my problem or my customer's?

The short answer: it is legally your customer's problem and practically yours, because your customer cannot produce the passport without your data. This article explains who is responsible, what will be asked of you, how to split the work, and when each step has to happen.

Who is legally responsible

Article 77(1) of Regulation (EU) 2023/1542 requires that from 18 February 2027 every LMT battery, every industrial battery with a capacity above 2 kWh, and every EV battery placed on the market or put into service in the EU has an electronic record — the battery passport. The obligation sits with the economic operator placing the battery on the EU market.

For a battery made outside the EU, that is normally the EU importer: the company established in the EU that first makes the battery available there. If you sell into the EU without an importer — directly to EU customers, for instance — you need an EU-established economic operator before you can lawfully place batteries on the market at all, typically an authorised representative acting under your mandate. That party then becomes the responsible operator for the passport too.

Two consequences follow:

  • The importer carries the liability, including the duty under Article 41 to verify that the manufacturer has done its part before the battery is placed on the market. Importers are now writing passport data delivery into supply contracts, and some will not take delivery without it.
  • Batteries already on the EU market before 18 February 2027 do not need a passport retroactively. The date applies to batteries placed on the market or put into service from then on. A pack that your importer has sold before the date is out of scope; the next container is not.

What your importer will ask you for

The Commission's guidance "Digital Batteries Passport – data points by category" (v3.2, 19 October 2026) lists 71 data points, labelled per battery category. The full list is in our free checklist. Grouped by who actually holds the information, the request to a non-EU manufacturer looks like this.

You, as pack manufacturer — once per model:

  • Identification: manufacturer name and address, manufacturing plant, battery category and model, battery mass, rated capacity.
  • Composition: chemistry, hazardous substances, fire suppressant type, critical raw materials, share of renewable content.
  • Performance and durability at placing on the market: nominal and limit voltages, original power capability and limits, cycle life to 80% state of health, round-trip efficiency, internal resistance, temperature range, expected lifetime, and the reference test the figures come from.
  • Labelling and conformity: the EU declaration of conformity, the separate-collection and heavy-metal symbols, and the waste-prevention information required by Article 74.
  • Restricted tier (visible only to legitimate-interest parties and authorities): cathode, anode and electrolyte materials, component part numbers, spare-part sources, dismantling instructions and safety measures.

Your cell supplier: detailed chemistry and critical-raw-material content, if you do not have it on file.

Your test lab: the cycle-life and performance test documents. These sit in the authorities-only tier, but they must exist and be linkable.

You, per shipment: the list of serial numbers, because the passport is issued per battery, not per model.

Not required for February 2027, and worth saying so explicitly in your contract to avoid being asked for them prematurely: carbon footprint declaration and class (the calculation rules under Article 7 are not adopted), recycled-content shares for cobalt, lithium, nickel and lead, and the supply-chain due diligence report, which follows from August 2027.

After the sale: state-of-health values and battery status (original, reused, repurposed, remanufactured, waste) are dynamic data in the restricted tier. They come from the battery management system or the operator, not from you, but your BMS has to be able to produce them.

Your know-how is not published

The most common objection from manufacturers is that the passport exposes proprietary information. It does not. Article 77(2) puts cathode and anode chemistry, electrolyte, part numbers, dismantling instructions and test reports behind access control: persons with a legitimate interest and authorities see them, the public does not. The public layer is nameplate data, performance figures, conformity and end-of-life information — most of which is already on your datasheet. What you lose is the option of a datasheet that is wrong.

How the work is usually split

A workable division, in the order it has to happen:

  1. Contract. Agree who issues, hosts and updates the passport, in what format and by when you deliver data, and that carbon footprint, recycled content and due diligence are out of scope until their acts apply.
  2. Model data once. You deliver the model-level data above — spreadsheets, PDFs and test reports are fine; they get mapped on the other side.
  3. Mapping, validation and signing. The importer, or the DPP service provider working for the importer, maps your data to the 71 data points for the right category, flags every gap before anything is published, and signs and hosts the passports.
  4. Identifiers before production. The QR code goes on the battery (Article 13(6)) from 18 February 2027, printed or engraved, visibly and indelibly. The identifier and its URL therefore have to exist before the battery leaves your factory. This is the step exporters most often discover too late: the passport pipeline runs ahead of labelling, not after shipment.
  5. Serials per shipment. You send the serial list; one passport per battery is issued from the model data.
  6. Registry. The importer, or its authorised service provider under Implementing Regulation (EU) 2026/1778, registers the identifiers in the EU DPP Registry. The registry is live since 20 July 2026, and the Commission published its API and battery data model on 30 October 2026.
  7. Updates. Supplier substitutions, status changes and state-of-health values go into new passport versions. The QR code and URL stay the same, so nothing is relabelled.

The timeline, counted back from 18 February 2027

  • Now to December 2026. Inventory the data per model. Chase the test reports and the cell supplier's composition data; those have the longest lead times. Decide the identifier scheme with your importer (usually GTIN plus serial).
  • December 2026 to January 2027. First passports issued for the models that will ship after the cutoff. QR artwork goes into production labelling.
  • January to February 2027. Serial-level issuance for every battery leaving the factory that will be placed on the market after 18 February. Registration of each passport's identifier in the EU DPP Registry, live since 20 July 2026 — the operator's organisation must be verified there first.
  • In parallel, watch three things: the access-rights implementing act (Q4 2026), the battery data model for the registry, and the Omnibus VIII battery amendments on LMT pack removability and spare-part batteries, which are in Parliament and not adopted.

Where PassportLab fits

PassportLab works for the EU importer, or for the manufacturer on the importer's behalf. Your technical data arrives through a supplier data request in whatever format you have; we map it to every data point for the battery category, flag what is missing, issue one signed passport per serial number, host it, and prepare the registry submission for the responsible operator. The importer authorises us as their service provider in the registry, and registration runs through the importer's own verified Registry account.

If you export batteries to the EU and have not yet had this conversation with your importer, now is the time. Book a readiness call — in English, with your importer on the line if you like — or start by checking whether your batteries are in scope and downloading the 71-point checklist to see what you already have.

Last reviewed: 29 October 2026. Regulatory status reflects the Commission's published guidance and schedule at that date.

Sources

Battery passports, done for you
Send us your raw product data. We return a compliant battery passport within 30 days of receiving it, and keep it current.