Skip to main content
All Articles

Second-Life Batteries and the Battery Passport: Reuse, Repurposing, Remanufacturing and Waste

A battery passport is not finished when the battery is sold. It has to follow the battery through its whole life: state-of-health updates, a status change when it is reused, repurposed or remanufactured, a new passport for its second life, and finally waste. Here is what changes at each stage, who is responsible, and how to keep it straight.

Ileana Sofronie 7 min read
Battery Passport
Second Life
Repurposing
Circular Economy
State of Health

Most of the conversation about the EU battery passport is about the day a battery is placed on the market. But the Regulation was written with the whole life of the battery in mind, and the passport is designed to change along the way. The biggest change comes when a battery leaves its first application: an EV pack becoming stationary storage, an e-bike battery being remanufactured, or a pack reaching the end of its life.

This article follows a battery through those stages and explains what the passport has to show at each one.

Stage 1: in service, and the data that changes

From the day it is placed on the market, part of the passport is dynamic. The state-of-health part (Annex XIII, point 4) holds values that move over time: remaining capacity, capacity fade, power fade, internal resistance increase, full cycles, negative events, operating conditions and, for EV batteries, the state of certified energy. Which of these are mandatory depends on the battery category; the Commission's guidance (v3.2, 19 October 2026) labels each one for EV, LMT and industrial batteries.

Two things follow:

  • Someone has to feed those values in. The source is usually the battery management system. Article 14 requires the BMS of stationary storage, LMT and EV batteries to hold up-to-date data on the parameters that determine state of health and expected lifetime. The passport is where that data becomes visible to the people entitled to see it.
  • Those values are restricted. State-of-health data and expected lifetime (#60) are open to persons with a legitimate interest, not to the public. See who can see what in a battery passport.

Stage 2: the status changes

Battery status (#67) is a mandatory data point for every category, and it has five values: original, reused, repurposed, remanufactured and waste. A new battery starts as original. Every later value marks a turning point in its life, and the change has to be traceable: when it happened, who made it, and from what to what.

That traceability isn't just good practice. A buyer of a used battery, a recycler or an authority looking at a passport needs to trust that "original" really means the battery has never been reworked. A status field anyone can overwrite silently is worth little.

Stage 3: the second life gets its own passport

When a battery is prepared for re-use, repurposed or remanufactured and placed on the market again, the Regulation moves responsibility for the passport to the economic operator who places it back on the market. The battery gets a new passport, linked to the original one (Article 77).

In practice:

  • The original passport stays. Its status changes (to repurposed, for example), and it gains a link to the new passport.
  • The new passport belongs to the second-life operator. It describes the battery as it is now, in its new application, and links back to the original.
  • History isn't lost. Anyone with the right access can follow the chain from the second-life battery back to its first life: original chemistry, original manufacturer, original test data.

For second-life operators, a well-kept original passport is commercially valuable. A repurposed EV pack with a complete state-of-health history is easier to price, insure and sell than one with a gap.

Stage 4: waste

When the battery becomes waste, the status changes to waste. The Regulation provides that the passport ceases to exist once the battery has been recycled. Until then, the passport's dismantling information, composition detail and safety measures are exactly what the recycler needs.

Who is responsible, at a glance

StageResponsible for the passport
Placed on the marketThe economic operator placing it on the EU market (manufacturer or importer)
In serviceThe same operator. State-of-health data typically comes from the BMS, telematics or service data
Re-used, repurposed or remanufacturedThe operator who places the battery on the market again, with a new passport linked to the original
Waste, until recycledThe status becomes waste; the passport ends once the battery is recycled

What to set up now

  1. Plan the dynamic data from day one. Decide which state-of-health values your batteries will report, where they come from, and how often. A passport that only ever shows its launch values doesn't hold up for long.
  2. Make status changes auditable. Every change should record who, when, from and to, in a log that can't be quietly rewritten.
  3. Keep the QR code stable. The battery's QR code must keep working through every status change. Point it at a stable address (a GS1 Digital Link, for example), never at a file. See One Passport Per Battery.
  4. If you're a second-life operator, ask for the original passport first. Its data, its state-of-health history and its status are your starting point.

How we handle it

In the passports we build, state-of-health values and status changes come in through the dashboard or by API, one battery at a time or in batches from a BMS or telematics system. Every changed field is written to a hash-chained audit log, so a silent rewrite would break the chain. Starting a second life creates the new passport, links both passports in each direction, and records the status change on the original. The QR code on the battery never changes.

If you place EV, LMT or industrial batteries on the EU market, or give them a second life, start with the free 71-point checklist, or book a call about your battery types.

Not legal advice. The regulation text is binding.

Sources

Battery passports, done for you
Send us your raw product data. We return a compliant battery passport within 30 days of receiving it, and keep it current.